Page 11 of 22
Re: What Did You Do In The Reloading Room This Week?
Posted: Thu Dec 20, 2018 8:09 pm
by crazy2medic
Spent most of today in my reloading room (yeah!) Sorted through 200 25-06 brass separating them by manufacturers, put the dingy ones in the tumbler, necked down 100 of them to 6mm, primed them and managed to get 50rds loaded. Straightened the reloading room, and now just have to find me a range day!
Re: What Did You Do In The Reloading Room This Week?
Posted: Thu Dec 20, 2018 8:21 pm
by jason812
6mm-06 is intriguing.
Re: What Did You Do In The Reloading Room This Week?
Posted: Thu Dec 20, 2018 8:24 pm
by SQLGeek
I have a press and most of my gear. Need to degrease my dies and get them setup and then I'll finally be loading.
Re: What Did You Do In The Reloading Room This Week?
Posted: Thu Dec 20, 2018 8:52 pm
by Beiruty
I reloaded 30 rds of the 6mm Creedmoor. SS Cleaned all 40SW cases on hand
Re: What Did You Do In The Reloading Room This Week?
Posted: Thu Dec 20, 2018 9:02 pm
by crazy2medic
So the day was productive one for more than just me!
Re: What Did You Do In The Reloading Room This Week?
Posted: Thu Dec 20, 2018 9:06 pm
by crazy2medic
jason812 wrote: Thu Dec 20, 2018 8:21 pm
6mm-06 is intriguing.
It's been an interesting project and expensive so it's taken me sometime to get to where I am now! Hopefully I'll get some range time soon, sighting it in to start at 200yds and then decide wether to sight it in at 400yds and then adjust it for 600yds or just go straight for 600yd dead on!
Re: What Did You Do In The Reloading Room This Week?
Posted: Thu Dec 20, 2018 9:22 pm
by longtooth
No real time to load anything. I probably have a small back stock. Just swept the floor and threw out some trash.
Re: What Did You Do In The Reloading Room This Week?
Posted: Thu Dec 20, 2018 9:35 pm
by flechero
Got my 38 Super toolhead set up on the 550
and started loading a few test loads with a few bullet types I have on hand... have 3 more bullet types on order to test in the coming weeks.
Also decapped and 1500 45acp brass and about 500 9mm for wet tumbling.
Re: What Did You Do In The Reloading Room This Week?
Posted: Mon Jan 07, 2019 11:13 am
by Deitz83
Loaded and tested my first 223 rounds. Everything worked extremely well. I wish I had a problem too go and chase. I was kinda disappointed that things went so well. Also, cleaned 3000 rounds of 40 S&W , 2000 rounds of 9 mm and 750 of 45 ACP.
Re: What Did You Do In The Reloading Room This Week?
Posted: Mon Jan 07, 2019 11:47 am
by flechero
Deitz83 wrote: Mon Jan 07, 2019 11:13 am
I wish I had a problem too go and chase. I was kinda disappointed that things went so well.
You say that now...
Re: What Did You Do In The Reloading Room This Week?
Posted: Mon Jan 07, 2019 12:13 pm
by Beiruty
Renovating the Garage (Reloading shop).
1) Fresh paint done
2) New floating Polymer tile floor done
3) 3 new SS cabinets done
Next
4) New Electric outlets and LED ceiling lights
5) Garage door insulation
Future project,
1) complete insulation and AC/Heat pump.
2) Custom wall mounted cabinets
Re: What Did You Do In The Reloading Room This Week?
Posted: Mon Jan 07, 2019 1:46 pm
by kayt00
I started building a reloading "room".
Re: What Did You Do In The Reloading Room This Week?
Posted: Wed Feb 06, 2019 10:03 pm
by bblhd672
Tonight my neighbor introduced me to reloading by providing the equipment and knowledge, I supplied the brass, powder, primers and bullets.
Reloaded 40 rounds of .308 with 168gr Sierra MatchKing.